Digi Connect ME 9210模組是根據 Digi最新的功能強大的NS9210處理器體積及其緊湊的嵌入式模組。
使客戶可以實施下一代領先的支持網路功能的產品並且保持了和已有的 Digi Connect ME 系列產品在結構尺寸和接腳定義上
的完全兼容。
本模組通過獨特的晶片內置的靈活接口模塊(FIM)可以提供面向特定應用的不同接口選擇 (CAN, 1-Wire, UART等) ，
同時還保留了串口。
Digi Connect ME 9210還適合多種進階核心模組應用，支持多達10 個共享的GPIO，外部中斷和一系列諸如 I2C 、SPI等標準接口。
對於定製的嵌入式應用來說，基於ThreadX支持IPv6功能的Digi JumpStart Kits開發套件是NET+OS開發平台，實現了易於使用和負擔
得起的開發解決方案。
開發包提供了快速和高性價比生成集成高性能網路解決方案的靈活和安全的嵌入式應用所需要的所有組件。
易於使用和高性價比的Digi JumpStart Kit 開發套件減少了產品設計風險，縮短了產品上市時間。
你可以選擇無需許可證費用可靠和靈活的基於ThreadX的 NET+OS 平台，還可以選用Linux 環境獲得社區的支持和軟體函數庫優勢。

產品規格
Hardware
* 32-bit Digi NS9210 processor @ 75 MHz (ARM926EJ-S)
* On-chip 256-bit AES accelerator
* Flexible Interface Modules (FIM)
      * 300 MHz DRPIC165X CPU
      * 2k program/192 bytes data RAM
* On-board memory
      * 2/4 MB NOR flash
      * 8 MB SDRAM
* High-speed TTL serial interface
      * Full signal support for TXD, RXD, RTS, CTS, DTR, DSR and DCD
      * Hardware/Software flow control
* Serial Peripheral Interface (SPI)
      * Master data rate up to 16.7 Mbps
      * Slave data rate up to 7.5 Mbps
* I2C v1.0 bus interface
      * 7-bit and 10-bit address modes
* 10 shared GPIO ports with
      * Up to 3 external IRQ options
* Power management modes
      * On-the-fly clock scaling
      * Low power sleep modes
      * Configurable scaling/wake-up events (EIRQ, UART, Ethernet, etc.)
* Software watchdog
* On-board power supervisor
* Wave-solderable design
      * No clean flux process

Network Interface
* Physical layer: 10/100Base-T
* Data rate: 10/100 Mbps (auto-sensing)
* Mode: Full or half duplex (auto-sensing)
* Connector: RJ-45 w/magnetics
* 802.3af power pass-through
      * Mid- and end-span

Pinouts
The table below provides a complete overview of the pinout and available configuration options:

Digi JumpStart Kits 開發套件

Digi Connect ME 9210 Digi JumpStart Kit for NET+OS 7
開發套件包括:
* Quick start guide
* Digi Connect ME 9210 module
      - 75 MHz NS9210, 4 MB Flash, 8 MB SDRAM
* Digi JumpStart Kit development board
      - RS-232 serial port, GPIO screw terminal, test points,
        application connectors, prototyping area,
        RS-232 console port (JTAG), 9-30VDC power supply
* Digi JTAG Link USB 2.0 hardware debugger
* Digi NET+OS CD
      - NET+OS 7, Digi ESP IDE, BSP source code, sample code
* Documentation and development board schematics
* Power supply and accessories
      - External wall power supply with adapters,
        Ethernet cable, serial cable

Digi Connect ME 9210 development kit for Digi Embedded Linux 4
開發套件包括:
* Quick start guide
* Digi Connect ME module w/JTAG
      - 75 MHz NS9210, 4 MB Flash, 8 MB SDRAM
* Digi JumpStart Kit development board
      - RS-232 serial port, GPIO screw terminal, test points,
        application connectors, prototyping area,
        RS-232 console port (JTAG), 9-30VDC power supply
* Digi Embedded Linux DVD
      - Digi Embedded Linux, Digi ESP IDE, source code,
        boot loader source code, sample code
* Documentation and development board schematics
* Power supply and accessories
      - External wall power supply with adapters,
        Ethernet cable, serial cable